Pro inputs
Plug in turntables, DJ mixers and wireless mics — with pro voice processing and multitrack recording.
Add an input
- In the studio mixer, press + Add input (or use Input 1).
- Tap the device button and open the Device picker. It lists every microphone, interface, mixer and app-audio option, and below it you choose how it's used: Microphone, Mixer / music source (Music / line) or Two mics on one interface. Allow microphone access first so device names show.
- Microphone (mono, with voice processing) — browser echo cancellation, noise suppression and auto gain can be switched on or off.
- Mixer / line in (stereo, no processing) — for DJ mixers, turntables and instruments. It stays stereo and dips under voice when talkover is active.
- Two wireless mics (split stereo) — gives each mic its own processing, fader, mute and meter.
Every input has Gain (−12 to +24 dB), a live meter and Set level automatically, which sets the input gain so peaks sit around −6 dBFS and glides the fader back to 0 dB over 2 seconds. If the strip shows CLIP, turn the gain down. If a red Echo warning appears, your mixer is sending AirDeck’s music back in — follow the steps in the warning, or use Stop sending decks to my computer speakers or Echo cancel this input.
Presets, echo cancellation, noise suppression, EQ, Enhancer, Voice FX, voice clips and MIDI live under Advanced.
Talkover ducks decks, playlists, pads, AutoDJ audio and every Mixer / line input. It never ducks a voice-mode input.
Turntables
Turntables need a phono preamp. Use a turntable with a built-in preamp, a separate phono preamp, or a DJ mixer / USB interface with a PHONO input. Connect it to your computer by USB and pick it in Music / line mode.
DJ mixer
If your mixer has a USB audio output, plug it in and choose it as the device. Otherwise connect the mixer's booth or record output to a USB audio interface's line input.
Dual wireless mics
Set the receiver (DJI Mic, RØDE Wireless GO, Hollyland Lark and similar) to split / stereo mode with safety channel off, so each mic is on its own side. Choose Split stereo → 2 mics.
Recommended gear by budget
- Simple: a USB dynamic mic, or a basic 2-input USB interface.
- Flexible: a dual wireless mic kit, or a 2–4 input USB interface with a phono preamp for turntables.
- Full setup: a DJ mixer with USB audio, or a multi-input interface.
Avoid Bluetooth mics and headsets: while the mic is on, Bluetooth switches to low-quality call audio.
iPhone and iPad
iPhone and iPad open one input device at a time. On iPhone use one USB interface or a split-stereo wireless receiver. Laptops and Android phones can open several devices at once.
Voice processing
Voice inputs have presets: Off, Natural, Radio Voice, Podcast, Loud Room and Custom (high-pass, noise gate, compressor, de-esser, low / presence / high EQ). Each input remembers its preset. If AirDeck warns that your device is struggling, set the preset to Off.
Voice FX
In the Show panel, Voice FX adds reverb, echo or robot to the host mic. Tap again to turn it off.
Multitrack recording
- In the Show panel, switch Multitrack on before you go live.
- When the show ends, press Download ZIP for one file per channel, or Save to Library (saved as Recordings, within your storage limit; files over 300 MB are ZIP only).
Guest tracks are recorded as AirDeck receives them. Guests who join after the show starts are in the main recording but don't get their own track.
MIDI controllers
MIDI works in Chrome or Edge on a computer or Android — not on iPhone or iPad.
- In the Show panel, open Controller and press Enable MIDI, then pick your device.
- Press Learn, click a fader, button or pad in the studio, then move a control on your controller.
- Press Done learning. Mappings are saved to your account for that controller.
Faders use soft takeover: move the control past the on-screen position to pick it up, so levels never jump. See also Getting started.